|
The weight is probably the only drawback, but it beats using passlode gas cartridges and much less problematic. I have'nt had a problem with nails not setting.ever.
My company purchased the gun to avoid the whole compressor and hose situation. Its alot quicker especially when you only need to install a couple pieces of molding.
I'm a trim carpenter, and custom cabinet installer, so I use this gun on a regular basis. The battery is still holding up, and I rarely have to charge it.
At first I was skeptical, especially because I've given up on buying yellow tools. However, this gun has been in good working condition for over 1 year, and thats heavy use all year.
It has jammed a couple times, but usually if you hit a screw or nail in the wood. Definitely worth the money.
A little, but my wife had no problems nailing up our crown molding. The unit is big compared to an air version but never was an issue in corners.
No more lugging around a compressor and hose. This is the greatest thing since sliced bread.
We had now issues driving 2.5in nails. We have done two rooms of crown molding and the battery shows no sign of slowing down.
It has a power setting that allows you to find the sweet spot for the wood you are working with. Heavy.
I recommend this nailer to everyone.
With all the wainscoting, beadboard, crown, baseboard, chair rail and every other imaginable kind of trim in this old victorian, the nailer functioned flawlessly. I never counted how many nails you could do on a charge - we never ran it down. This is all covered in the manual, although I don't recall it making a point of thinking about the positioning of the chisel point. Well, it sure isn't light, although I find it comfortable to hold and easy to use, even standing on a step ladder putting up crown molding over my head. Not having to deal with both batteries and gas tilted me in favor of the DeWalt.
Other reviewers has mentioned the DeWalt is heavy. I love it. I wanted the ease of use of a cordless, which pretty much narrowed it down to DeWalt or Paslode. We shot many, many boxes of nails and wore out two rubber noseguards without a single jam.The only issue is shooting thin nails into hard word.
Sometimes you need to turn the nailer so the long edge of the chisel point is across the grain so it cut through it instead of following it.The angled magazine makes it surprisiningly easy to get into small locations. The bottom line. My 26 year old daughter has no problems using it in any position either (it's her house). While most of the wood is pine, it's old first growth southern yellow pine that's almost as hard a oak. If I had one complaint, it's that there's no good position to put it down, other than standing on the battery.
Faced with a major overhaul of a 120 year old house, I wasn't looking forward to doing all the trim with a hammer and nailset, so I purchased a finish nailer. Actually better than my straight magazine brad nailer, which is much smaller overall.Pay attention to which model you're looking at when comparing prices - the 618K has one battery while the 618KA comes with two, and batteries are expensive. I have the KA, and when we were doing trim we never had a problem running out of battery - in fact, many days we didn't have to switch at all. On days when we used it heavily, we'd just swap batteries every few hours when we took a break. Sometimes it'll even make a u-turn, so you need to think about where you put your hands when using this tool. In that position, it's top heavy, so you sure don't want to put it on the top of your step ladder while you're fiddling some piece of crown molding into position. It uses the same nails as the Paslode (in fact, that's all I use since none of my local stores carry the DeWalt nails).
And while the weight didn't bother us using it, it's a lot when it's hanging on your belt by the hook.I like it so much a bought a DeWalt brad nailer when they came out. If you don't pay attention to the direction of the chisel point of the nails relative to the grain, the nail will follow the grain. Same for knots or other defects in the wood. The only negative is the weight, but that never really bothered us when we were actually using it. Unfortunately, I'm not nearly as happy with the brad nailer, but that will be a different review.
Complete waste of $350. Plenty of jambs with the 15 and 16. It's impossible to contact the company. Don't buy a dewalt cordless nailer. Call the local repair dealer and they tell you they can fix the tool for the price of a new one. Many problems still exist with Dewalts design as of July 2008. Motor failed after 2000 nails. Look at the Dewalt website.
My 15 ga nailer has problems as well -- doesn't advance the nails. I have to manually advance the nails. Your left high and dry after the tools fail. Get a "cumbersome" pneumatic nailer - at least they work.
It's nice not having to lug around a compressor and being able to nail without cords or hoses. I just bought my second DeWalt DC618 nailer. This nailer has plenty of power, even with hard woods like oak. I do a fair amount of remodeling with my two sons. This nailer has been great. The reason I needed a second nailer is because my son will not give back the nailer he "borrowed" for a very large house rebuild that he is doing. I think a third nailer is probably in our future.It has become an indispensable tool.
|
